Road-building equipment

For sealing cracks in the pavement as asphalt distributor used car ED-10A. It is based on the chassis of GAZ-53A consists of the following major components and systems: tanks for bitumen, two bins for sand, Swing bin, filling bitumen system, pneumatic, fuel and hydraulic systems, spetskabiny, left and right side, and rear boxes, electrical equipment.

Bitumen tank - welded frame mounted on the chassis and fixed ladders. The body of a layer of thermally insulated glass, retained removable lining. At the top of the tank is sliding sunroof with a filter through which it is filled with bitumen, as well as inspect, clean and repair the internal

cavity. The tank is equipped with a float level gauge and thermometer. Inside it is flue to heat the bitumen. In the left (while moving) hole burner flame tube set, right - close the lid, which is removed during cleaning of the pipe from sludge. Right before the release of the flame tube is welded to her vent (exit of the combustion products). On the left and right sides of a hinged spetskabinoy installed bins for sand, used for sealing cracks of asphalt concrete pavement. Download the bunker sand is provided by its rotation on its hinges screw mechanisms. The system consists of pouring asphalt distributor, machinery management, bitumen pump, wash tank, three-way valves bituminous flush tank flushing mechanism of control valves, two discharge valves, manual valves with two cranes and three-way valve manual valves.

Distributor - square, consists of a body, 15 jets, rods with your fingers, three fingers and arm rails. Inside the shell is divided by horizontal partitions, allowing bitumen to circulate through the distributor. Bitumen pump - gear type, driven by a hydraulic engine. The system allows the bitumen filling the following operations: avtogudronirovanie, the circulation of bitumen through the valve, hand filling, a small circulation of bitumen, after flushing and after avtogudronirovaniya manual filling, draining of bitumen from the system.

We recommend to look

• Generator ESS-81-4
  Generator ESS-81-4 provides 20 kW of electricity consumers. The drive of the generator from the motor shaft base unit via PTO, driveshaft, intermediate support and the V-belt transmission. The compressor provides the blasting and spray charts. Elektrovibrotrambovka designed to seal freshly placed mass with a width of the repair area is less than 500 mm. Elektrovibrokatok used to seal freshly placed mixture to [...]
• The drive compressor
  The drive is made ​​from the compressor PTO engine GAZ-53A through the gearbox, driveline and transmission belt. On the gear drive compressors mounted gear pump NSh-10E, which serves the work of hydraulic machines. In the working position hopper hydraulic cylinder rises thermos, allowing automatic translation of the bucket truck-mounted on the rear bodywork and manual vibratory rollers of the transport to working position. Bucket-truck [...]
• The main features of the machine from the DE-5 model DE-5A
  The main features of the machine from the DE-5 model DE-5A - the presence of her benzoelektricheskogo unit and working with electrical equipment (compressor, elektrovibrokatka, elektromolotkov). The hydraulic drive hopper, a thermos and a rear side of the machine is provided with hydraulic cylinders, hydraulic pump mounted on the gearbox mounted on the gearbox car chassis, equipped with a mechanism of inclusion; drive the compressor and elektrovibrokatka elektromolotkov carried out from [...]
• Road remonter 5320
  Road remonter 5320 is designed to eliminate damage to the asphalt coating in the form of potholes, subsidence, cracks, waves lapping. Repairs made ​​hot and cold mixtures, as well as a way of impregnation with bitumen coatings or asphalt emulsion. Special equipment is mounted to the chassis ZIL-130 and two-axle trailer 2APS-4, 5. On the chassis of the car are: hydraulic crane with a capacity of 400 kg, power plant [...]
• Remixer
  Remixer - is, in fact, the car "Repaver", equipped with additional dosing and mixing units. Warmed up the old asphalt coating loosen knives, and then screw valve and located behind the blade is fed into the mixing unit equipped with two shafts. Fresh mix from the hopper conveyor enters the dosing unit, which sends it to the mixer, where the old and the new mass [...]