vehicles for maintenance and repair of city roads

Milling Machines Rotary Equipment CO-705

April 13, 2009 | Filed under: Control osmotrovye work for plow-brush snow removal equipment
(Not yet rated)
Загрузка ... Loading ...
Milling Machines Rotary Equipment CO-705

Milling and rotary machine KO-705: prior to placement on the long-term storage of dismantled vehicles wash it, wipe and check the technical condition and if necessary repaired. After cleaning, check the status of weld metal, the completeness of equipment and color. Replace the oil on schedule in the conical and cylindrical gear drive milling (oil is poured to the level of filler plug) remove the hydraulic cylinders, washed inside and outside of their diesel fuel, wipe the exterior surfaces. Cylinder rod retracts to failure, the holes in the cylinders and the connecting fitting oil lines closed with rubber stoppers or special screw plugs. Speakers of the stem is covered with grease, wrapped in waterproof paper and tied with twine. All unpainted surfaces coated with rustproof hardware with grease.

mounted on the stand. Hydraulic cylinders and rubber hoses for rent on storage.

During the period of seasonal maintenance check and the technical condition of the carburetor, its parts and components, including jets. Remove the fuel pump, disassemble, clean it, check the condition of parts and assemblies when tested on the stand, wash tank.

Inspect the battery (the electrolyte density and cell voltage under load). In the area of ​​cold climate in the preparation of the battery to operate, if necessary, bring the gravity of the electrolyte to the rules and always warmed her. Removed from the motor generator, the tape, check the status of the collector, brushes, bearings, the inner cavity is purged with compressed air, collect the generator, the studs and tighten the pulley nut. The generator test stand at the rated load, and then set it on the engine. Check the relay controller and adjust it to the voltage to the time of the year. Removed from the engine starter motor, clean the outer surface of the oil and dirt, disassemble and check the status of collector brushes, contacts, relays, tighten the screws attaching the intermediate bearing and bushing wear on the cover of the drive. Assemble the starter and check the adjustment of stroke gear drive starter and work on the stand at idle and full braking, and then install a starter on the engine. Removed from the motor breaker distributor, disassemble it and inspect the bearing rolling disk chopper lever, roller and cam. Gather breaker distributor, lubricate the shaft axis of the lever and the cam sleeve and check the angle of the stand of the closed state of the breaker contacts, the angle of rotation of sparking, sparking continuity, the work of the centrifugal and vacuum automatic ignition, and then set the breaker distributor on the engine.



We recommend to look

  • Remixer
    Remixer - is, in fact, the car "Repaver", equipped with additional dosing and mixing units. Warmed up the old asphalt coating loosen knives, and then screw valve and located behind the blade is fed into the mixing unit equipped with two shafts. Fresh mix from the hopper conveyor enters the dosing unit, which sends it to the mixer, where the old and the new mass [...]
  • The drive compressor
    The drive is made ​​from the compressor PTO engine GAZ-53A through the gearbox, driveline and transmission belt. On the gear drive compressors mounted gear pump NSh-10E, which serves the work of hydraulic machines. In the working position hopper hydraulic cylinder rises thermos, allowing automatic translation of the bucket truck-mounted on the rear bodywork and manual vibratory rollers of the transport to working position. Bucket-truck [...]
  • Removing the plow equipment for watering, washing machine
    For watering, washing cars - removal of plow equipment (lowered plow) rasshplintovka and removal of suspension attachment plow fingers, toes turning away the nut ball mount coupler plow frame and disconnect from the towing frame, lifting ladders and finger mounting frame lift cylinder. Then - the removal of brush equipment, in which: giving way bolts right cheek brush frame, left [...]
  • Bunker thermos
    Hopper provides storage thermos of hot asphalt mix. The mixture is fed into the truck through the open (with cylinder) hopper bin, after which the mixture is transported to the site of work. The torque from the surface of the power takeoff shaft, flanged to the gearbox base unit is transmitted to the input shaft of the hydraulic pump, and from the bottom of the shaft - the input shaft of the generator [...]
  • Milling and reclaimers K0-705R
    Milling and reclaimers K0-705R for the transfer of snow from the trees, and heaps on the back area or loading it into the vehicle consists of a frame, casing, milled feeder, rotor drive mechanisms of the working body and the guide vane. Working equipment mounted to the front frame of the lift truck using special hooks and secured by four bolts. Milling feeder consists of two [...]

Leave a comment