Tank - welded construction oval in cross section, inside which there are filters that control the pipe, and two breakwater. The bottom flange of the tank to set the central valve, which connects the cavity of the tank to the suction pipe. The valve is out of the cab with hydraulic cylinder tractor. A centrifugal pump LC-6 provides water to the nozzles. The pump is driven by the PTO through the flow forming gear and gear pump. At the watering-washing trailer has four attachment - two front and two behind. On the pressure side mounted three-way valve and two valves that let you control the water supply to the nozzles in the tank.
Plow-brush equipment PNSCH K0-705 is used to clean pavements of snow. This attachment consists of a plow, mounted in front of the tractor and brush, fortified behind the rear-wheel drive tractor.
Blade - welded from sheet 4 mm thick, reinforced with box-shaped profiles. In the lower part of the sectional fixed rubber knives. Blade is mounted with the fingers on a welded bracket that captures the special hinged to the front frame of the lift truck and connected to it with bolts. It is installed at an angle of 55 ° to the axis of the tractor, providing snow removal on the right or left side. Brush, mounted behind a tractor on a special bracket consists of a frame, pile brush, gearbox, mountings and systems of signs. Frame it - from the welded channels. At the ends of the plate welded to it, which on one side (the right to go) fixed gear, but on the other - a cast-iron support (opposed to the gearbox). The bottom of the frame are welded two brackets which are connected by longitudinal rods with a brush, to which are attached draft regulation of signs. These clamps provide constant thrust pile brush to the road surface, which reduces vibration and wear cloth. Reducer brushes - one-step, cylindrical. The input shaft is connected to its drive shaft with the gear flow forming, on the output shaft is fixed brush.
We recommend to look
- Sidewalk machine T-469
Sidewalk machine T-469 on the chassis of the UAZ-469B - a plow, snow blower brush, equipped with a winter working equipment, which consists of a blade with a rubber blade and cylindrical brushes with nylon bristles. Welded blade mounted in front of the car and the front wheels can rotate around a central pivot to the right and left at 60 ° relative to the longitudinal axis of the machine. The brush is placed between [...]
- Sidewalks-sweeper TUM-975
Sidewalks-sweeper TUM-975 has special equipment mounted on a special self-propelled chassis, performed on three-wheel circuit with front drive and rear steering axles, which consists of a dual wheel. Daylight saving equipment consists of two main chute and a cylindrical brushes, hopper, and estimates of the type of pneumatic dust control. At the bottom of the hopper set screw, which provides unloading of [...] - Sidewalks-sweeper K0-708
Sidewalks-sweeper K0-708 on the basis of self-propelled chassis T-16M has two versions: for the summer (equipped with a sweeping, cleaning equipment) and winter (equipped with a plow, brush and peskorazbrasyvayuschim equipment). In the summer of machine is used for cleaning dirt from the pavement in the winter - to clean the pavement of the fresh snow, sprinkling them with sand or chemical materials. The base chassis has a front and [...] - Power transmission spreader
Power transmission drives the spreader conveyor drive and tipping the spreading equipment. Its main elements - the PTO, drive shaft, gear drives the conveyor, conveyor chain, hydraulic drive. The torque from the transmission base car passed the lower power takeoff shaft to the pump drive the spreading disk, and the top (through the drive shaft) - on the pump drive belt. [...] - Sweeping equipment
Sweeping up the equipment frame, tapered gear, cylindrical brush, chain drive with damper device chain hoist brushes. The brush is installed between the front and rear wheels at an angle of 62 ° to the longitudinal axis of the machine. The torque on the shaft of the brush is passed from the bottom of the shaft of the transfer case through the propeller shaft, conical reducer and chain drive. Frame brushes, consisting of [...]
Loading ... 
